MBE9A4i ECU, Ignition Only up to 4-cylinders

MBE9A4i ECU, Ignition Only up to 4-cylinders

MRP Without VAT: £345.00
MRP With VAT:  £414.00 MBE9A4i ECU, Ignition Only up to 4-cylinders Minimum Quantity :

MBE9A4i ECU, Ignition Only up to 4-cylinders

MBE9A4I

This ECU is designed for ignition only control.  It can run distributor or distributorless engines up to 4 cylinders; its possible inputs are crank speed & throttle angle.  It can be used with ignition against speed or if a throttle position sensor is fitted to the carburettors, it can be programmed to change the ignition according to the open of the butterflies. It uses USB communication from your laptop, which is then converted by a small piece of hardware (MBE985) that converts the USB in CAN, which is a more stable system, used by car manufacturers worldwide.
 
All our MBE ECUs will be loaded with a base map as close as possible to your requirements. In addition they are capable of being adjusted by the user via a computer. All ECUs are fully tested during manufacture.
 
Crank Sensor & Trigger Wheel Input
Crank sensors are most commonly of the inductive type, you can normally use the original crank sensor. If your engine uses the hall effect type, MBE ECUs can be built to order. 
MBE write special code to allow the use of a range of different trigger wheels, most commonly 60-2(GM/VW/Bosch), 36-1(Ford), 24-1(Suzuki hayabusa) & 24-2(Suzuki Busa 2008 & other late Japanese bike engines). Other trigger wheels may become available, download Easimap 6 to check current types. We can supply a range of specialist sensors & suitable trigger wheels for applications that currently have no trigger wheel.
A special piece of software has been written by MBE called soft start, this was produced due to known problem with the standard starter motors, that if the battery got a bit low sometimes the engine would kick back on starting and engage the starter clutch. This would, if you were lucky only damage the starter clutch itself, but if unlucky could break off part of the engine cases. Without going into too much detail, the ECU allows the engine to get up to speed during cranking before attempting to start the engine, if the engine does not reach sufficient speed it will not allow the engine to start, so damage can not occur.
 
Throttle Position Sensor Input
Throttle position sensors are used to inform the ECU of how much load is being applied.  We sell a range of throttle position kits to use with Weber & Dellorto carburettor kits. 
 
Ignition & Coil Input
The MBE9A4i has four ignition drives, that can be fired either sequentially or in wasted spark mode, depending on requirements & set-up. The normal MBE9A4i has built in amplifiers so there is no need for expensive external units. You can use four individual coils (standard coils as used on the Suzuki hayabusa) or twin coil pack (GM, Peugeot:COIL-4 or Ford:COIL-9). It is most commonly used with a wasted spark coil pack (COIL-4).
If you have coils with built-in amplifiers, an MBE9A4i can be built to order.
 
Water Temperature Input
Water temperature can be used on the MBE9A4i, but because this unit is designed to be simple to use, it is not a compulsory input. The MBE water temperature input circuitry allows the use of 2 different types of sensor, either the MBE/Bosch/Nippon Denso/Lucas water temperature sensors (all use the same calibration) (WTS1)or Ford type which uses a completely different resistor value. This is selectable within the ECU.
 
Barometric Pressure & Boost (MAP) Input
The pressure inputs can be used to compensate for Barometric & Manifold pressure changes, but they are never used on a simple installation e.g. 4-cylinder carburettor ignition systems. 
The boost/MAP pressure sensor compensates for changes in manifold pressure, most commonly used with turbo applications. The sensor input is 0 - 5V, it is fully calibratible by the end user. The ECU will normally comes with calibration either for the MBE/GM sensor (car engine) or standard Suzuki/Nippon Denso sensor (bike engine). The ECU can make changes to fuelling & ignition according to pressure. 
The barometric pressure sensor compensates for atmospheric pressure changes due weather conditions & altitude. The sensor input is 0 - 5V, it is fully calibratible by the end user. The ECU will normally come with calibration either for the MBE/GM sensor (car engine) or standard Suzuki/Nippon Denso sensor (bike engine). 
 
Power Shift
Power shift can be configured in various different options, it's simplest form is a single cut time. With use of 'complete on target gear', this allows the ECU to vary the cut time to lengthen or shorten it depending on how long the gear change takes. This time can vary dramatically depending on conditions (requires gear position sensor input). Powershift now has the option to either cut the spark, retard the spark or a combination of the two depending user requirements. There is an option for 'cut when pin low', this normally for use with external devices. Also there are many safety features built in, such as, lock out timers & continuous assert to protect against power shift being triggered accidentally.  
 
Tachometer Output
The MBE9A4i ECU produces a square wave 12V output, this is configurable from within the ECU for the number of pulses that occur on the tacho signal per engine cycle. This means it can be programmed to suit your own tachometer's requirements. The tacho signal also has programmable duty cycle. If you intend on using our MBE9MD display or a dash such as an AIM that can be configured to receive the information over CAN, you would be able to use the tacho output from the MBE for a different function since it would be no longer needed. 
 
Shift light & Warning systems Output
The shift light output is configurable in several ways, it could be set-up as a simple shift light which is purely rpm dependant. If you add a low pressure switch or pressure sensor to the MBE, you can set-up a low oil pressure warning, which can also be rpm dependant. This can be configured to trigger an oil light or linked to the shift light, so one output can do 2 functions. We also have designed a bleeper system, which many competition drivers use & find more unmissable.
 
Radiator Fan Output
The MBE9A4i is fully programmable, not only can it be programmed to switch off & on at given temperatures but it can even be programmed to run on after the ignition is switched off for a given length of time or until a specified temperature is reached. If you are programming for specified temperature after engine off, you would need to run an electric water pump to ensure water circulation.  
 
Launch & Traction Control Output
Launch control on the MBE9A4i can be configured to use up to 7 different launch maps. Each map can be set with the different launch rpm & can be externally selected by the user depending on track conditions.  
The launch control is activated with a clutch switch & dash or steering wheel button with a sequence as follows;
- Depress the clutch, which activates clutch switch.
- Then push steering wheel button, which arms launch.
- Release steering wheel button, launch then becomes active.
- Depress throttle by desired amount, will bring the engine rpm to your preset launch limiter (according to selected setting)
- Then release clutch, the ECU then progresses though the launch map maintaining the programmed rev limits, which you have set to increase over a longer or shorter period of time as desired.
Traction control is being developed to use several strategies, from the simplest type which will be rate of engine change not requiring additional sensors, then rate of change with gear position suitable for cars with sequential gearboxes & finally rate of change with slip requiring wheel speed. This software is under development.
 
Data Logging/Histograms Output
The MBE9A4i has an inbuilt memory that can record a series of histograms & engine hour clock for recording total engine run time. This will enable the engine builder or programmer to monitor engine life if any misuse of the engine has occurred, such as excessive engine temperature or over-revving. 
It is also possible to log direct to your laptop from the ECU any information being transmitted by your ECU provided your laptop is connected.
 
Data Logging/CAN data stream Output
The MBE9A4i has a user configurable CAN data stream, this can be set up to be used with many external data loggers & displays. You would need to contact your data-logger/display manufacturer for the correct protocols. 
 
Data Logging/CAN data stream Output
The MBE9A4i has a user configurable CAN data stream, this can be set up to be used with many external data loggers & displays. You would need to contact your data-logger/display manufacturer for the correct protocols. 
 
More functions are continuously added to the MBE9A4i, please download Easimap 6 for the latest updates.